Reebok rx8200 manual

Visit our website at. Previous Page. Next Page. Reebok fitness user's manual treadmill rbtl 34 pages. Page 3 Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in sandals.

Page 13 calories fat calories Page 14 time remaining minutes per mile Page 15 all speed settings will move one col- umn to the left if all of the indicators in the Current Segment column are lit, the speed settings will move downward so that only the highest indicators in the columns will appear in the program display.

Enter your age and a maximum speed setting. When the key is in- serted, the manual mode will automatically be selected. To select a custom program, first press the Program Select button repeatedly until one of the custom See pages 18 and 19 for connecting instructions. To use iFIT. Plug one end of the audio cable into the jack on the front of the treadmill near the power cord. Page 21 If the speed or incline settings are too high or too low, you can manually override the settings at any time by pressing the Speed or Incline buttons on the console.

Additional options are soon to be available. See www. To use programs from our Web site, the treadmill must be connected to your home computer. The information mode also al- lows you to switch the console from miles per hour to kilometers per hour. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. Find the symptom that applies, and follow the steps listed.

If further assistance is needed, please call our Customer Service Department toll- free at , Monday through Friday, 6 a. Mountain Time excluding holidays. Page 28 Several studies have reported that regular walking at moderate to brisk speeds appears to increase bone density.

Specifically, Fradin and his colleagues that year-old subjects who walked at least 30 min- utes per day had higher bone mineral content than subjects who walked less than 30 minutes per day. This is especially important for individu- als over the age of 35 or individuals with pre- existing health problems. The pulse sensors are not medical devices. Various factors, including the user's move- ment, may affect the accuracy of heart rate readings.

Key No. This manual is also suitable for: Rx Print page 1 Print document 34 pages. Rename the bookmark. Ensure the power supply is isolated and switched off. Ensure the correct fuse type and rating has been fitted to both the equipment and the power cable. Connect the lead to the receiver input connector and then to the power supply.

Note: Refer to the Reference Guide for all power supply, fuse replacement, safety, EMC information and operating conditions. The following points should be noted when making signal connections to the receiver:. Adaptor cables are used to provide the connector type required for the installation. This equipment should not be operated unless the cooling fans are working and there is free-air flow around the unit. After a short period of initialization the following screen is displayed on the Front Panel:.

When the equipment is switched on it will assume the control mode that was set when the power was turned off. This could be either:. Ensure that the incoming feed is connected to connector RF IN 1. To configure the unit for Satellite input, navigate to the front panel Input menu Source Configure menu and carry out the following steps:.

Select SAT input. Set the Modulation scheme and FEC. Set the set the LNB power output. A description of each of these User Settings can be found in the Reference Guide.

Ensure that the incoming feed is connected to connector IP IN 1. Select IP input. Set up the MAC Mode parameters. Ensure that the incoming feed is connected to connector G To configure the unit for G. Select G input. Welcome to ManualMachine.

We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. All rights reserved. Disclaimer No part of this document may be reproduced in any form without the written permission of the copyright owner.

Contents Contents 1 Introduction Connect the receiver to the power supply as follows: 1. Switch on the power supply. You can only view or download manuals with.

Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.

Buy as many as you need. View and download manuals available only for. Register and get 5 for free.